• Common options
• Introduction
• Properties
• Placement
• Visualisation
• Allow label overlapping

Common options

Introduction

Regardless of which advanced labelling method is chosen, there are some options that are common to all three methods. These options provide a great degree of control over the configuration of the labels.

These options are accessible via the buttons on the labelling tab of the Layer properties dialog box and are described below.

Properties

The 'Properties' button provides access to a large number of label options.

Clicking this button opens the dialog box shown in the figure below:

The following properties can be set in this dialog box:

• Name

• Font type

• Font colour

• Text size (fixed size or adjusted to fit on text area)

• Label expression (one or more)

  This is where the actual label is specified. The possibilities are:

  • Strings (enclosed in quotes)
  • Fields from the attribute table (enclosed in square brackets)
  • Mathematical expressions
  • Combinations of the above

• Label all features / filter features with a SQL statement

  The SQL filter allows the user to apply the defined label to certain features only.

• Background style

  Select a style (picture) as a background for the labels. Clicking the 'Select' button opens the following dialog box:

  

  Select a label background style

  When gvSIG is installed, the installer automatically creates a directory called 'Styles' in the directory /user/gvSIG/. This is where all the label styles are saved (by clicking the 'Save' button).

  Once a label style has been selected, it is possible to modify its properties by clicking the 'Properties' button. This opens a dialog box (shown below) where the user can insert one or more text boxes in which to place the different label expressions that have been created. These text boxes can also be moved or deleted and it is also possible to upload a new image from disk.

  

  Configure the label background style

Note: It is not possible to apply a background style if the label orientation is set to "Following the line" (see the Placement section below).

Placement

Clicking the Placement button opens the Placement properties dialog box where the following properties can be configured: location, orientation, duplicates, etc. The options available in this dialog box will depend on the geometry of the layer in question (point, line or polygon):

Point layer

If the layer is a point layer, the following options can be configured:

• Point settings

This options allows the user to place the labels on top of the points, or else to offset them around the points.

In the latter case, the label position can be selected from pre-defined placement configurations, which are accessed by clicking the Change location button. This opens the Placement priorities selector from where existing placement styles can be selected. It is also possible to modify a placement style by highlighting it and clicking the Properties button:

By using the tools on the right and applying them to the location grid on the left it is possible to set the label position priority relative to the point:

1 = High precedence

2 = Normal precedence

3 = Low precedence

0 = Prohibited

• Duplicate labels

Here it is possible to choose between 'Remove duplicate labels' (eliminate any duplicate labels and only draw one label per feature), 'Place one label per feature', and 'Place one label per feature part' (in the case of multipoint features).

Line layer

For line layers the following options are available:

• Orientation

The label can be oriented horizontally, parallel or perpendicular to the line, or can be set to follow the line.

• Position

The label can be placed above, on or below the line.

• Location

Place the label at the beginning, middle or end of the line, or at the best position.

• Duplicate labels

The options here are the same as for point layers (described above).

Polygon layer

If the layer is a polygon layer, the Placement properties dialog box provides the following options:

• Polygon settings

Labels can be set to be always horizontal, or else to follow the orientation of the polygons (always straight). There is also an option for fitting the labels inside the polygons. This last option is used to ensure that labels are placed inside polygons even if they have islands, or are U-shaped.

• Duplicate labels

These options are the same as for point and line layers.

Multigeometry layers

In the case of multigeometry layers (dwg, dxf, gml...) the Placement properties dialog box contains a tab for each of the three geometries (points, lines, polygons). These tabs are identical to those shown above.

Visualisation

Clicking the 'Visualisation' button opens a dialog box which allows configuration of the range of scales at which labels will be shown.

The user can choose to use the same scale range as the feature layer (set under the General tab of the layer properties dialog), or else can specify a scale range at which the labels will be visible (this scale range is independent of the range applied to the geometries of the layer).

In the example shown above, labels in the view are only displayed between the scales of 1:500000 and 1:1000000.

Allow label overlapping

Finally, there is a check box that controls whether labels may overlap or not.

If this box is checked then all labels are drawn, even if they overlap each other. If this box is left unchecked, only non-overlapping labels are drawn and all overlapping labels are eliminated.